How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
We've stumbled on this post relating to How to Install a Bathtub below on the web and reckoned it made sense to discuss it with you on this site.

Setting up a bath tub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall surface to eliminate the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the task and also are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly help you mount a new bath tub in your shower room if you have actually already acquired a new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices and product checklist must comprise the following:
Preparing for the Installation
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the bath tub as well as likewise examine the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub ought to wait up until the bathtub has actually been utilized at the very least once as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in place with the maker provided backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous kind needs to be attached to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can break fairly very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Hopefully you enjoyed our topic about Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to read our piece of content. Do you know about somebody else who is interested in the niche? Do not hesitate to promote it. Thanks so much for going through it.
Request Appointment Report this page